Lenovo PX04PMB. SSD capacity: 1920 GB, SSD form factor: 2.5", Component for: Server/workstationNon-Volatile Memory Express (NVMe) is new PCIe 3.0 high performance SSD technology that provides high I/O throughput and low latency. NVMe interfaces remove SAS/SATA bottlenecks and unleash all of the capabilities of contemporary NAND flash memory. Each NVMe PCI SSD has direct PCIe 3.0 x4 connection, which provides at least 2x more bandwidth and 2x less latency than SATA/SAS-based SSD solutions. NVMe drives are also optimized for heavy multi-threaded workloads by using internal parallelism and many other improvements, such as enlarged I/O queues.The Lenovo NVMe Enterprise Mainstream PCIe SSD have the following features: 2.5-inch drive (U.2) or 3.5-inch drive bay form factor Based on the Toshiba PX04P drives, PX04PMBxxx 19nm MLC NAND (128 Gb/die) 3 drive-write-per-day (DWPD) SSD for mixed read-write workloads Direct PCIe 3.0 x4 connection for each NVMe drive, resulting in up to 4 GBps overall throughput. Full Power-Loss-Protection and End-to-End Data Protection Low power consumption (maximum 18.5 W)Enterprise Mainstream SSDs and Enterprise Performance SSDs have similar read and write IOPS performance, but the key difference between them is their endurance (or lifetime) (that is, how long they can perform write operations because SSDs have a finite number of program/erase (P/E) cycles). Enterprise Mainstream SSDs have a better cost/IOPS ratio but lower endurance compared to Enterprise Performance SSDs. SSD write endurance is typically measured by the number of program/erase (P/E) cycles that the drive incurs over its lifetime, listed as the total bytes of written data (TBW) in the device specification.The TBW value assigned to a solid-state device is the total bytes of written data (based on the number of P/E cycles) that a drive can be guaranteed to complete (% of remaining P/E cycles = % of remaining TBW). Reaching this limit does not cause the drive to immediately fail. It simply denotes the maximum number of writes that can be guaranteed. A solid-state device will not fail upon reaching the specified TBW. At some point based on manufacturing variance margin, after surpassing the TBW value, the drive will reach the end-of-life point, at which the drive will go into a read-only mode.Because of such behavior by Enterprise Mainstream solid-state drives, careful planning must be done to use them only in mixed read-write environments to ensure that the TBW of the drive will not be exceeded before the required life expectancy.For example, the 1.92TB NVMe 2.5" Enterprise Mainstream PCIe SSD has an endurance of 10,412 TB of total bytes written (TBW). This means that for full operation over five years, write workload must be limited to no more than 5,705 GB of writes per day, which is equivalent to 3.0 full drive writes per day (DWPD). For the device to last three years, the drive write workload must be limited to no more than 9,509 GB of writes per day, which is equivalent to 5.0 full drive writes per day.

Характеристики

SSD form factor 2.5" SSD capacity 1920 GB Interface PCI Express 3.0 Memory type MLC NVMe Yes Component for fiber Channel Read latency 100 Вµs Write latency 30 Вµs Sequential write speed (ATTO) 2350 MB/s Sequential read speed (ATTO) 3100 MB/s Maximum write (4KB) 105000 IOPS Maximum read (4KB) 660000 IOPS Mean time between failures (MTBF) 2000000 h Hot-swap Yes NVMe version 3.0 Power consumption (max) 18.5 W Operating temperature (T-T) 0 - 40 В°C Storage temperature (T-T) -40 - 70 В°C Operating relative humidity (H-H) 5 - 95% Storage relative humidity (H-H) 5 - 95% Operating vibration 2.17 G Operating shock 1000 G Maximum non-operating altitude 12192 m Maximum operating altitude 5486 m Width 70 mm Depth 100 mm Height 15 mm Weight 150 g Package width 133 mm Package depth 174 mm Package height 63 mm Package weight 500 g Colour of product Black Cooling type Heatsink